Calculate Land Area in Square Feet: Rectangle, L-Shape, Trapezoid
To calculate the area of a rectangular lot, multiply its length by its width: a 75 × 140 ft lot is 10,500 ft². To get acres, divide square feet by 43,560, so that lot is 0.241 acre. If the front and back are different widths, average them and multiply by the depth; if the lot is L-shaped, split it into rectangles and add them.
That covers most house lots, gardens and fenced paddocks. Below are the formulas, a quick way to check that a "rectangle" really has square corners, worked examples, and when you need a different method.
The basic formula: length × width
- Measure one long side and one short side, in the same unit.
- Multiply them. Feet × feet gives square feet; metres × metres gives square metres.
- Convert if you need to: divide by 43,560 for acres, by 9 for square yards, or by 10.764 for square metres.
Worked example
A lot is 75 ft wide and 140 ft deep.
- Area: 75 × 140 = 10,500 ft²
- Acres: 10,500 ÷ 43,560 = 0.241 acre
- Square yards: 10,500 ÷ 9 = 1,167 yd²
- Square metres: 10,500 ÷ 10.764 = 975 m²
The same formula works at field scale. A pasture 660 ft long and 330 ft wide is 217,800 ft², exactly 5 acres.
Check that the corners are square
Length × width is only correct when all four corners are right angles. Many lots that look rectangular are slightly skewed, and you cannot see a few degrees of skew by eye.
Two quick checks:
- Measure both diagonals. In a true rectangle they are equal. For the 75 × 140 ft lot, each diagonal should be √(75² + 140²) = 158.8 ft. If one diagonal is 155 ft and the other 162 ft, the lot is a parallelogram or an irregular shape, not a rectangle.
- Use 3-4-5 at a corner. Mark 3 ft along one side and 4 ft along the other; the straight distance between the marks should be 5 ft. Use 30-40-50 ft for better precision on a large lot.
If the opposite sides are equal but the diagonals are not, the area is less than length × width. If the opposite sides themselves differ, use one of the methods below.
Tapered lots: the trapezoid formula
Lots on a curving street or near a cul-de-sac are often wider at the back than at the front. When the front and back lines are parallel and the side lines angle outward, the lot is a trapezoid.
When the front and back are parallel:
Area = (front + back) ÷ 2 × depth
The depth must be measured straight across, at right angles to the front and back, not along a slanted side line.
Example: frontage 60 ft, back line 80 ft, depth 150 ft.
(60 + 80) ÷ 2 × 150 = 70 × 150 = 10,500 ft², or 0.241 acre.
If neither pair of sides is parallel, this formula no longer applies. Averaging all four sides will overestimate the area; split the lot into two triangles instead, as shown in how to calculate the area of irregular land.
L-shaped lots: split or subtract
An L-shaped lot is two rectangles. There are two ways to get its area, and they should give the same answer.
Example: the outer outline is 100 ft wide and 90 ft deep, but a 60 × 30 ft corner belongs to the neighbor.
- Split: the full-width strip is 100 × 60 = 6,000 ft². The narrower strip behind it is 40 × 30 = 1,200 ft². Total: 7,200 ft².
- Subtract: the outer rectangle is 100 × 90 = 9,000 ft². Take away the missing corner, 60 × 30 = 1,800 ft². Total: 7,200 ft².
7,200 ÷ 43,560 = 0.165 acre.
The same idea works for T-shapes, U-shapes and lots with a driveway strip: cut the shape into rectangles (and triangles where an edge is slanted), find each one, and add them up. For a triangular corner piece, see the area of triangular land.
Measuring the sides
- Tape or measuring wheel. Pull a tape tight and level; a sagging tape reads long. A wheel is faster on lawns and dirt roads but less precise on rough ground.
- Start from known points. Survey pins, fence corners and the plat give better starting points than a hedge line.
- Measure each side twice, ideally from opposite ends. Write down every number; the diagonals are your check.
- Slopes. Property area is normally the horizontal (map) area. On a slope, a tape laid along the ground reads longer than the horizontal distance, so hold it level or expect a slightly high figure.
Skip the tape: tap the corners on a map
If you can see the corners from above, a satellite map is faster than any tape, and it handles odd shapes without splitting anything by hand.
Field Maps with Area Measure runs on iPhone and iPad (iOS 17 or later). Tap each corner of the lot on a satellite map, using the magnifier loupe to place points precisely, and the app shows the area and perimeter straight away, in square feet, square yards, acres, square metres or hectares. An L-shape is simply six corners instead of four. Where trees hide the corners, walk the boundary with GPS and the app records the path and closes the shape. Each measurement is saved with a name. Measuring area, perimeter and distance is free. GPS tracking and measuring work offline; a map area you have never opened needs a connection to load its imagery. There is no Android version yet.
Phone GPS is typically accurate to about 3–5 m (10–16 ft) under open sky, and worse under trees or near buildings. On a small house lot, tapping corners on the satellite image usually beats walking the line; on a field of several acres, either method works well.
Quick conversions
- 1 acre = 43,560 ft² = 4,046.86 m²
- 1 yd² = 9 ft²
- 1 m² = 10.764 ft²
- 1 hectare = 10,000 m² = 2.471 acres
- A square acre is about 208.7 × 208.7 ft
FAQ
How do I calculate the square footage of a lot?
Multiply the length by the width in feet. A 50 × 120 ft lot is 6,000 ft². This assumes square corners; check that the two diagonals are equal.
How do I convert lot square footage to acres?
Divide by 43,560. A 10,500 ft² lot is 0.241 acre, and a 21,780 ft² lot is exactly half an acre.
What if the front and back of my lot are different widths?
If the front and back lines are parallel, average them and multiply by the depth measured at right angles. If no sides are parallel, split the lot into triangles instead.
Is my measurement good enough for a sale or a permit?
It is a good estimate for planning, fencing, sod or comparing with your deed. For a sale, a boundary question or a permit, rely on a licensed surveyor and the recorded plat.